You have heard the phrase “the devil is in the details.” That has never been truer than in the installation of waterproofing and air barrier products. The vast majority of leaks occur at transitions, terminations, and penetrations. But they don’t have to. Polyguard offers a variety of products that bridge transitions between dissimilar products, are compatible with the most building products and are easy to use.

Detail Sealant PW™

Detail Sealant PW™ is a new generation, environmentally friendly, non-isocyanate adhesive/sealant that replaces silicone and urethane sealants. Non-corrosive and non-staining, Detail Sealant PW™ is a low VOC/HAPS free, high performance, flexible sealant that is solvent free.

It is also used in many below grade waterproofing applications at terminations and penetrations as well as a trowel-on rough opening flashing/waterproofing above grade.

  • Cures rapidly, even at low temperatures, and retains its properties to -75°F
  • Non-corrosive and non-staining
  • VOC/HAPS free high-performance solvent-free sealant
  • Provides a continuous smooth surface
  • Available in easy to use 3 Gallon Pails or 20 oz. Sausages

105-12 Flashing

105-12 Flashing membrane is a 105 mil, strong, pliable self-adhesive sheet consisting of high-density polyethylene film bonded to a layer of rubberized asphalt waterproofing compound with slit release sheet to conform to 90″ angles. 105-12 Flashing is used in exterior flashing applications to deflect water. Applications include spandrel beams, sills, copings, door and window headers, and flange flashings.

  • Can be field fabricated to meet various job site conditions without cracking as compared to some metal systems
  • High puncture resistance provides protection against abuse by other trades during and after installation
  • Rubberized asphalt membrane adheres tenaciously to the surface and itself eliminating blow-off and tears, before exterior wall installation

Balconyguard™ Outside Corner Boot

Balconyguard™ Outside Corner Boot is a 60-mil combination of rubberized asphalt and polyethylene. The adhesive surface is covered with a release liner to be removed prior to application of the Balconyguard™ membrane. It is applied to the outside face of the balcony at the wall-to-balcony interface.

  • Easy installation for less detailing time
  • Release liner for ease of application
  • Can also be used with the Underseal® PRM™ Membrane and the 650 Sheet Membrane
  • Saves time & labor on the job site

Underseal® Inside Corner Boot

Underseal® Inside Corner Boot is a 60-mil combination of rubberized asphalt bonded to polyethylene. The adhesive surface is covered with a release liner which will be removed prior to application. It is applied in the inside corner to reinforce and seal the corners of the Underseal® Underslab membrane. Underseal® Inside Corner Boots are designed for use on all inside corners.

  • Preformed corner boot conforms to the film side of the Underslab membrane to seal any possible pinhole condition
  • Applied in the inside corner to reinforce and seal corners
  • Release liner for ease of application
  • Saves time & labor on the job site

Underseal® Outside Corner Boot

Underseal® Outside Corner Boot is a 60-mil combination of rubberized asphalt bonded to polyethylene. The adhesive surface is covered with a release liner which will be removed prior to application. Underseal® Outside Corner Boots are designed for use on the outside corner to reinforce and seal the Underseal® Underslab membrane. Corners can require a series of cuts, folds, flaps, and patching which can leave a pinhole in the corner. This preformed corner boot conforms to the side of the membrane to seal any possible pinhole condition and allow for faster, labor-saving installation of the system.

  • Used on the outside corner to reinforce and seal the Underseal® Underslab Membrane
  • Preformed corner boot conforms to the film side of the Underseal® Underslab Membrane to seal any possible pinhole condition
  • Release liner for ease of installation
  • Saves time & labor on the job site.

Underseal® Pit Top Corner Boot

Underseal® Pit Top Corner Boot is a 60-mil combination of rubberized asphalt bonded to polyethylene. The adhesive surface is covered with a release liner which will be removed prior to application of the Underseal® Underslab Membrane. Apply the Underseal® Pit Top Corner Boot in the corner to reinforce and seal the Underseal® Underslab Membrane. This preformed corner boot conforms to the film side of the Underseal® Underslab Membrane to seal any possible pinhole conditions.

  • Apply in the corner to reinforce and seal the Underseal® Underslab Membrane
  • Conforms to the film side of the Underseal® Underslab Membrane to seal any potential pinhole conditions
  • Release liner for ease of installation
  • Saves time & labor on the job site

LM-85 SSL

LM-85 SSL  is a two component, semi-self leveling, asphalt modified, urethane liquid membrane specifically formulated to be used in conjunction with Polyguard waterproofing membrane in Dual Core and pitch pan applications. LM-85 SSL can be applied down to 25°F (-4°C).

  • No solvents – 100% solids
  • UV stable for up to 3 months
  • Pourable sealer

LM-95

LM-95 is a two-part component urethane waterproofing membrane to be used in a variety of applications in conjunction with the Polyguard® waterproofing system.

  • Two-component fast cure urethane waterproofing membrane
  • Can be used for terminations and flashings to curbs and parapets on plaza decks
  • Can be used as a fillet at the junction of the footing and foundation, a collar around drain detailing areas, and as a termination flashing material for protrusions

Overseal Mesh™

Overseal Mesh is a 100% polyester, spunbond, needlepunch mesh and  is designed to be used with Polyguard Overseal-H™ Membrane and any other liquid membranes.

  • Excellent thermal properties
  • Pliable
  • Superior moldabilty
  • Durable
  • High dimensional stability
  • Inherently UV stable

Poly Cover

Poly Cover is a preformed dome-shaped tie back cover made with heavy duty, high impact ABS plastic. It is designed to cover protruding tie-back bolts less than 6″ in height in lagging and retention walls prior to application of the Underseal® Blindside™ Membrane.

  • Made with heavy duty, high impact ABS plastic
  • Designed to cover protruding tie-backs
  • Easy installation for less detailing time
Contact Us

We're not around right now. But you can send us an email and we'll get back to you, asap.

Not readable? Change text.

Start typing and press Enter to search