Contractors are the lifeblood of our success and business growth. We want to assist you in any way possible by making our products easy for you to find, easy for you to use, give you the support you need to install them and give you support after the job with competitive,  easy to access Warranties.

If you have a need not addressed on our website, please allow us to assist you. You may directly contact the Polyguard staff member listed for your location using the information provided on the Field Resource map.

You may also contact us using the form on this page and we will do our best to find a resource to assist you as soon as possible.

We have assembled a series of helpful tools specifically intended for our Contractor Customers.

Typical Systems & Applications

Underseal® Underslab Membrane

Underseal® Underslab Membrane is a tough, 85 mil pre-concrete pour waterproofing membrane/vapor barrier designed to virtually eliminate water and vapor transmission through concrete slabs on grade. In addition to protecting floor finishes and indoor air quality, Underseal® Underslab Membrane also acts as a barrier to methane and radon gas.

REQUIRED ITEMS  (products to complete a basic system, if you require additional options please refer to product page for a list of companion products.)

650 LT Liquid Adhesive Used to prime all structural concrete, masonry, insulation or wood surfaces prior to membrane installation. More Detail
California Sealant Used to seal all porous portions of Underseal® geotextile surface and promote adhesion of Polyguard sealants. More Detail
Detail Sealant PW™ VOC./HAPS free high-performance solvent-free sealant More Detail
Underseal® Fabric Tape Use around pipe penetrations and at end laps for patching damaged areas of the membrane More Detail
Underseal® Inside Corner Boot To be applied in the inside corner to reinforce and seal the corners of the Underslab membrane More Detail
Underseal® Outside Corner Boot For use on the outside corners to reinforce and seal the Underslab membrane More Detail
Underseal® Pit Top Corner Boot Preformed corner boot used to reinforce and seal the Underslab Membrane More Detail

Underseal® Blindside™ Membrane

Underseal® Blindside™ Membrane is a 73 mil, pre-concrete pour, strong sheet membrane waterproofing with a thick, cross-laminated, high-density polyethylene (HDPE) backing, laminated to a thick layer of proprietary waterproofing adhesive compound integrated into a nonwoven geotextile fabric.

REQUIRED ITEMS (products to complete a basic system, if you require additional options please refer to product page for a list of companion products.)

650 LT Liquid Adhesive Used to prime all structural concrete, masonry, insulation or wood surfaces prior to membrane installation. More Detail
California Sealant Used to seal all porous portions of Underseal® geotextile surface and promote adhesion of Polyguard sealants. More Detail
Detail Sealant PW™ VOC./HAPS free high-performance solvent-free sealant More Detail
Polyflow® 15 / 15P Prefabricated geocomposite vertical use drainboard with a compressive strength of 15,000 psf More Detail
Underseal® Fabric Tape Use around pipe penetrations and at end laps for patching damaged areas of the membrane More Detail

Underseal® PRM™

Thermoplastic Technology is behind the success of our signature Air Barrier, Airlok Flex®. This patented single component, cold liquid-applied, elastomeric, coating cures to form a durable Air Barrier membrane …

REQUIRED ITEMS  (products to complete a basic system, if you require additional options please refer to product page for a list of companion products.)

650 LT Liquid Adhesive Used to prime all structural concrete, masonry, insulation or wood surfaces prior to membrane installation. More Detail
Detail Sealant PW™ VOC./HAPS free high-performance solvent-free sealant More Detail
Detail Tape Use as detail strips on corners, penetrations, joints, and for patching damaged areas of the membrane. More Detail
Shur-Tac Liquid Adhesive Polymer emulsion based adhesive to provide excellent adhesion of self-adhering membranes More Detail

650 Sheet Membrane

650 sheet membrane is a strong, pliable, 60 mil, post-concrete pour self-adhesive waterproofing membrane/vapor retarder that virtually eliminates water and vapor transmission through concrete slabs.  650 sheet membrane …

REQUIRED ITEMS  (products to complete a basic system, if you require additional options please refer to product page for a list of companion products.)

650 LT Liquid Adhesive Used to prime all structural concrete, masonry, insulation or wood surfaces prior to membrane installation. More Detail
Detail Sealant PW™ VOC./HAPS free high-performance solvent-free sealant More Detail
Detail Tape Use as detail strips on corners, penetrations, joints, and for patching damaged areas of the membrane. More Detail
Shur-Tac Liquid Adhesive Polymer emulsion based adhesive to provide excellent adhesion of self-adhering membranes More Detail

Commercial Stretch Fluid-Applied Waterproofing

Thermoplastic Technology is behind the success of our signature waterproofing, Commercial Stretch. This patented single component, cold liquid-applied, elastomeric, coating cures to form a durable waterproofing membrane …

REQUIRED ITEMS  (products to complete a basic system, if you require additional options please refer to product page for a list of companion products.)

Detail Sealant PW™ VOC/HAPS-free high-performance solvent-free sealant More Detail
Polyflow® 15 / 15P Prefabricated geocomposite vertical use drainboard with a compressive strength of 15,000 psf More Detail

PRO 1000 Fluid-Applied Dampproofing

PRO 1000 is a patented, single-component, cold-applied, non-elastomeric, non-breathable, thermoplastic membrane.  It dries to a UV resistant, re-coatable hard coat protective film that stops water passage through a substrate. …

REQUIRED ITEMS  (products to complete a basic system, if you require additional options please refer to product page for a list of companion products.)

Detail Sealant PW™ VOC./HAPS free high-performance solvent-free sealant More Detail
Polyflow® 15 / 15P Prefabricated geocomposite vertical use drainboard with a compressive strength of 15,000 psf More Detail

Balconyguard™

Balconyguard™ is a 60 mil, cold-applied, adhesive waterproofing membrane to be used specifically on wood deck balcony structures that will be covered with concrete.  Our Balconyguard™ System includes custom …

REQUIRED ITEMS  (products to complete a basic system, if you require additional options please refer to product page for a list of companion products.)

105-12 Flashing 105 mil, strong, pliable self-adhesive sheet flashing More Detail
650 LT Liquid Adhesive Used to prime all structural concrete, masonry, insulation or wood surfaces prior to membrane installation. More Detail
Detail Sealant PW™ VOC./HAPS free high-performance solvent-free sealant More Detail

Deckguard® HT Roofing & Watershield Underlayment

Deckguard® HT is a high heat 40 mil roofing membrane composed of a high strength slip resistant spider web backing laminated to a high-performance high heat asphalt compound with a film release for ease of application. The …

REQUIRED ITEMS  (products to complete a basic system, if you require additional options please refer to product page for a list of companion products.)

Detail Sealant PW™ VOC./HAPS free high-performance solvent-free sealant More Detail
650 LT Liquid Adhesive Used to prime all structural concrete, masonry, insulation or wood surfaces prior to membrane installation. More Detail
Shur-Tac Liquid Adhesive Polymer emulsion based adhesive to provide excellent adhesion of self-adhering membranes More Detail

Tileguard™ Anti-Fracture Underlayment

Tileguard™ is a composite membrane of fabric and rubberized asphalt, 40 mils in thickness used to reduce the risk of cracking of ceramic tiles in a flooring application.  This elastomeric, self-adhesive membrane …

REQUIRED ITEMS  (products to complete a basic system, if you require additional options please refer to product page for a list of companion products.)

650 LT Liquid Adhesive Used to prime all structural concrete, masonry, insulation or wood surfaces prior to membrane installation. More Detail
Shur-Tac Liquid Adhesive Polymer emulsion based adhesive to provide excellent adhesion of self-adhering membranes More Detail

NW-75 Membrane for Parking Structures

NW-75 Membrane is designed for use prior to an asphalt overlay.  When placed on joints and cracks of pavement, it will waterproof and also reduce the extent and severity of reflective cracking.  It is commonly used …

REQUIRED ITEMS  (products to complete a basic system, if you require additional options please refer to product page for a list of companion products.)

LM-95 Two-component fast cure urethane waterproofing membrane More Detail
Underseal® Fabric Tape Use around pipe penetrations and at end laps for patching damaged areas of the membrane More Detail

Airlok® Sheet 400 NP /NPW

Airlok® Sheet 400 NP / NPW are each a 40-mil, 36” x 75’ laminated, modified-asphalt, self-adhesive, non-permeable sheet membranes bonded to a cross-laminated polyethylene sheet designed for air and moisture applications with a 60-day UV exposure. Rubberized-asphalt properties allow for self-sealing around fasteners, sealing of laps, and adhesion to the substrate at ambient application temperatures above 40°F (5°C). Our NPW winter formulation is recommended down to 25°F (-4°C) and rising. (Cut Sizes for Flashing)

REQUIRED ITEMS  (products to complete a basic system, if you require additional options please refer to product page for a list of companion products.)

650 LT Liquid Adhesive Used to prime all structural concrete, masonry, insulation or wood surfaces prior to membrane installation. More Detail
Detail Sealant PW VOC/HAPS-free high-performance solvent-free sealant. More Detail

Airlok® Sheet 400 HT / NP

 Airlok® Sheet 400 HT / NP is a 40-mil, 36” x 75’ laminated, modified asphalt, self-adhesive, non-permeable sheet membrane bonded to a cross-laminated polyethylene sheet designed for air and moisture applications. Provides a 60-day UV exposure with a broad service/performance temperature up to 260°F. Rubberized-asphalt properties allow for self-sealing around fasteners, sealing of laps, adhesion to the substrate at ambient application temperatures above 40°F (5°C). Designed for use under metal cladding and copings. (Cut Sizes for Flashing)

REQUIRED ITEMS  (products to complete a basic system, if you require additional options please refer to product page for a list of companion products.)

650 LT Liquid Adhesive Used to prime all structural concrete, masonry, insulation or wood surfaces prior to membrane installation. More Detail
Detail Sealant PW™ VOC/HAPS-free high-performance solvent-free sealant. More Detail

Airlok® Sheet UV 400 NP / NPW

Airlok® Sheet UV 400 NP / NPW is a 40-mil, 36” x 75’ self-adhesive, non-permeable composite sheet membrane, consisting of a foil/polyscrim film, laminated to a layer of rubberized asphalt designed for air and moisture applications with a 1-year UV exposure. Rubberized-asphalt properties allow for self-sealing around fasteners, sealing of laps, and adhesion to the substrate at ambient application temperatures above 40°F (5°C). (Cut Sizes for Flashing)

REQUIRED ITEMS  (products to complete a basic system, if you require additional options please refer to product page for a list of companion products.)

650 LT Liquid Adhesive Used to prime all structural concrete, masonry, insulation or wood surfaces prior to membrane installation. More Detail
Detail Sealant PW™ Is a new generation, environmentally friendly, non-isocyanate adhesive/sealant that replaces silicone and urethane sealants. More Detail

Airlok® Sheet UV Ultra 400 NP

Airlok® Sheet UV Ultra 400 NP is a 40-mil, 36” x 75’ self-adhesive, non-permeable composite sheet membrane, consisting of a foil/ polyscrim film, laminated to a layer of rubberized asphalt designed for air and moisture applications with a 1-year UV exposure. Rubberized-asphalt properties allow for self-sealing around fasteners, sealing of laps, and adhesion to the substrate at ambient application temperatures above 40°F (5°C). (Cut Sizes for Flashing)

REQUIRED ITEMS  (products to complete a basic system, if you require additional options please refer to product page for a list of companion products.)

650 LT Liquid Adhesive Used to prime all structural concrete, masonry, insulation or wood surfaces prior to membrane installation. More Detail
Detail Sealant PW Is a new generation, environmentally friendly, non-isocyanate adhesive/sealant that replaces silicone and urethane sealants. More Detail

Airlok®Sheet 200 BU / NP

Airlok® Sheet 200 BU / NP is a 20-mil, 36” x 100’ laminated, butyl, self-adhesive, impermeable sheet membrane bonded to a cross-laminated polyethylene sheet designed for air and moisture applications. It provides a 60-day UV exposure and with a service/performance temperature range up to 240° F. The butyl properties allow for self-sealing around fasteners, sealing of laps, and adhesion to the substrate at ambient application temperatures 20°F (-7°C) and rising. (Cut Sizes for Flashing)

REQUIRED ITEMS  (products to complete a basic system, if you require additional options please refer to product page for a list of companion products.)

650 LT Liquid Adhesive Used to prime all structural concrete, masonry, insulation or wood surfaces prior to membrane installation. More Detail
Detail Sealant PW Is a new generation, environmentally friendly, non-isocyanate adhesive/sealant that replaces silicone and urethane sealants. More Detail

Airlok®Sheet UV 200 BU / NP

Airlok® Sheet UV 200 BU / NP is a 20-mil, 36” x 100’ laminated, butyl, self-adhesive, impermeable sheet membrane bonded to a cross-laminated polyethylene sheet designed for air and moisture applications. It provides a 60-day UV exposure and with a service/performance temperature range up to 240° F. The butyl properties allow for self-sealing around fasteners, sealing of laps, and adhesion to the substrate at ambient application temperatures 20°F (-7°C) and rising. (Cut Sizes for Flashing)

REQUIRED ITEMS  (products to complete a basic system, if you require additional options please refer to product page for a list of companion products.)

650 LT Liquid Adhesive Used to prime all structural concrete, masonry, insulation or wood surfaces prior to membrane installation. More Detail
Detail Sealant PW Is a new generation, environmentally friendly, non-isocyanate adhesive/sealant that replaces silicone and urethane sealants. More Detail

Airlok Flex®

Thermoplastic Technology is behind the success of our signature Air Barrier, Airlok Flex®.

  • Can be used in very cold conditions (down to -20°F)
  • Patented Thermoplastic Technology Reduces Application Costs & Exceeds Industry Standards
  • Transitional Membranes and Treatments can adhere to it eliminating touchup
  • Single component product eliminates mixing & inconsistent performance
  • Speedy Installation…up to 10,000 sq. ft. a day

REQUIRED ITEMS  (products to complete a basic system, if you require additional options please refer to product page for a list of companion products.)

Detail Sealant PW™ VOC/HAPS-free high performance solvent-free sealant. More Detail

Airlok Flex® NP-40

A high build, single component, water-based air barrier designed to meet specifications that require 40 dry mils in a non-permeable product.

  • Non-Permeable (0.7 perms)
  • Water-Based
  • VOC Content: Less than 20 (g/l)
  • Application temperature range of 40°F to 120°F
  • UV resistance of up to one year
  • 70 wet / 40 dry mils (23 sf /gal theoretical coverage rate)

REQUIRED ITEMS  (products to complete a basic system, if you require additional options please refer to product page for a list of companion products.)

Detail Sealant PW™ VOC/HAPS-free high performance solvent-free sealant. More Detail
650 LT Liquid Adhesive Used to prime all structural concrete, masonry, insulation or wood surfaces prior to membrane installation. More Detail

Airlok Flex® VP

Airlok Flex® VP is a water-based, permeable, above-grade air, weather and vapor coating for application over poured concrete, concrete masonry (CMU) and the following types of sheathing: paper-face, glass-face, foil-face, rigid insulation, plywood and oriented strand board (OSB).

  • Forms a durable protection with up to 100 PSI adhesive pull-off strength
  • Blocks inward moving water from penetrating through the coating to the substrate, and reduces energy loss
  • Low cost per square foot
  • UV resistance of up to one year
  • Easy to prep, easy to spray or roll and easy to clean up, saving hours and dollars
  • Available in Low Temp (LT) version with use in temperatures 20°F and rising

REQUIRED ITEMS  (products to complete a basic system, if you require additional options please refer to product page for a list of companion products.)

Detail Sealant PW™ VOC/HAPS-free high performance solvent-free sealant. More Detail

Airlok Flex® VP-40

A high build, single component, water-based, air barrier designed to meet specifications that require 40 dry mils in a permeable product.

  • Permeable (14 Perms)
  • Water-Based
  • VOC Content: Less than 50 (g/l)
  • Application temperature range of 40°F to 120°F
  • UV resistance of up to one year
  • 60 wet / 40 dry mils (26 sf / gal theoretical coverage rate)

REQUIRED ITEMS  (products to complete a basic system, if you require additional options please refer to product page for a list of companion products.)

Detail Sealant PW™ VOC/HAPS-free high performance solvent-free sealant. More Detail

Airlok Flex® WG

Airlok Flex® WG (Weather-Guard) is a permeable water based air barrier with exceptional UV resistance designed to meet the needs of thin mil specifications and applications.

  • Permeable (21 perms)
  • Water-Based
  • VOC Content: 79 (g/l)
  • Application temperature range of 40 to 120 degrees F
  • UV resistance of up to two years
  • 20 wet / 10 dry mils (80 sf / gal theoretical coverage rate)
  • Available in Low Temp (LT) version with use in temperatures 20°F and rising

REQUIRED ITEMS  (products to complete a basic system, if you require additional options please refer to product page for a list of companion products.)

Detail Sealant PW™ VOC/HAPS-free high performance solvent-free sealant. More Detail

AIRLOK® STPE SPRAY-N-ROLL

Airlok® STPE Spray-N-Roll  is typically used as a fluid-applied Air Barrier/WRB used prior to the installation of cladding. Typical applications include coating masonry, masonry cavity, poured and precast walls.  Additional applications include plywood, oriented strand board (OSB), and exterior-grade gypsum sheeting which shall be covered with an exterior facade.

 

  • Versatile spray or roll from one product
  • Can be used on damp or wet surfaces, product likes moisture
  • Unlike silicone products, Airlok STPE is compatible with virtually all common Building Materials
  • Single-component; ease of application with no need for mixing
  • Wide range of application temperatures from 40°F (5°C) up to 110°F (44°C)
  • Resistant to wash-off during rain events, extending the application time relative to inclement weather
  • High solids content of 90% for high yield and 0 g/l VOC

REQUIRED ITEMS  (products to complete a basic system, if you require additional options please refer to product page for a list of companion products.)

Airlok STPE Flash-N-Roll Fluid-applied WRB (Rolled on) and Window flashing. Durable, compatible with most building materials, can be used on wet/damp surfaces. Zero VOCs. More Detail
Airlok STPE Gun-N-Spread Fluid-applied flashing material. Troweled on above grade Window/Door rough openings. Compatible with most building materials. Can be used on wet/damp surfaces. Zero VOCs. More Detail
Airlok STPE Detail-N-Joint Fluid-applied, fiber-filled joint filler. Detailing compound used at transitions in the building process. Compatible with most building materials. Can be used on wet/damp surfaces. Zero VOCs. More Detail

AIRLOK® STPE FLASH-N-ROLL

Airlok® Flash-N-Roll is a single-component, cold-fluid-applied, Silyl Terminated Polyether (STPE) fluid-applied air barrier and/or flashing material; that combines the best of silicone and polyurethane properties. Typically used as a fluid-applied, rolled on above grade rough opening flashing/waterproofing used prior to the installation of doors and windows.

  • Unique roller application as window opening flashing
  • Can be used on damp or wet surfaces, product likes moisture
  • Unlike silicone products, Airlok STPE is compatible with virtually all common Building Materials
  • Versatile roll on flash or roll on membrane application from one product
  • Single-component; ease of application with no need for mixing
  • Wide range of application temperatures from 40°F (5°C) up to 110°F (44°C)
  • Resistant to wash-off during rain events, extending the application time relative to inclement weather

REQUIRED ITEMS  (products to complete a basic system, if you require additional options please refer to product page for a list of companion products.)

Airlok STPE Spray-N-Roll Fluid-applied WRB (Spray or roll). Durable, compatible with most building materials, can be used on wet/damp surfaces. More Detail
Airlok STPE Detail-N-Joint Fluid-applied, fiber-filled joint filler. Detailing compound used at transitions in the building process. Compatible with most building materials. Can be used on wet/damp surfaces. Zero VOCs. More Detail

AIRLOK® STPE GUN-N-SPREAD

Airlok® Gun-N-Spread is a single-component, gun and trowel cold-applied Silyl Terminated Polyether (STPE) fluid flashing material; that combines the best of silicone and polyurethane properties. Typically used as a fluid-applied, troweled on above grade rough opening flashing/waterproofing used prior to installation of doors and windows.

  • Versatile putty-knife application as window opening flashing
  • Can be used on damp or wet surfaces, product likes moisture
  • Unlike silicone products, Airlok STPE is compatible with virtually all common Building Materials
  • Single-component; ease of application with no need for mixing
  • Existing cured membranes readily receive additional application creating a monolithic transition
  • Wide range of application temperatures from 40°F (5°C) up to 110°F (44°C)
  • Resistant to wash-off during rain events, extending the application time relative to inclement weather

REQUIRED ITEMS  (products to complete a basic system, if you require additional options please refer to product page for a list of companion products.)

Airlok STPE Spray-N-Roll Fluid-applied WRB (Spray or roll). Durable, compatible with most building materials, can be used on wet/damp surfaces. More Detail
Airlok STPE Detail-N-Joint Fluid-applied, fiber-filled joint filler. Detailing compound used at transitions in the building process. Compatible with most building materials. Can be used on wet/damp surfaces. Zero VOCs. More Detail

AIRLOK® STPE DETAIL-N-JOINT

Airlok® Detail-N-Joint is a single-component, cold-applied, Silyl Terminated Polyether (STPE), fiber-filled, fluid joint filler and transition flashing material; that combines the best of silicone and polyurethane properties.  The typical detailing application includes Sheathing joints, penetrations and filling in imperfections on surfaces such as concrete walls and wood window bucks.

  • Versatile detail compound for application at transitions and flashing
  • Can be used on damp or wet surfaces, product likes moisture
  • Unlike silicone products, Airlok STPE is compatible with virtually all common Building Materials
  • Single-component; ease of application with no need for mixing
  • Existing cured membranes readily receive additional application creating a monolithic transition
  • Wide range of application temperatures from 40°F (5°C) up to 110°F (44°C)
  • Resistant to wash-off during rain events, extending the application time relative to inclement weather

REQUIRED ITEMS  (products to complete a basic system, if you require additional options please refer to product page for a list of companion products.)

Airlok STPE Spray-N-Roll Fluid-applied WRB (Spray or roll). Durable, compatible with most building materials, can be used on wet/damp surfaces. More Detail
Airlok STPE Flash-N-Roll Fluid-applied WRB (Rolled on) and Window flashing. Durable, compatible with most building materials, can be used on wet/damp surfaces. Zero VOCs. More Detail
Airlok STPE Gun-N-Spread Fluid-applied flashing material. Troweled on above grade Window/Door rough openings. Compatible with most building materials. Can be used on wet/damp surfaces. Zero VOCs. More Detail

Sales Tools

FileAction
Waterproofing Brochure (PDF)Download 

FileAction
Air Barrier Brochure (PDF)Download 

FileAction
Drainage Systems Brochure (PDF)Download 

Project Profile Sheets









HELPFUL TOOLS

NEED HELP?

  • P.O. Box 755 Ennis, TX 75120-0755
  • 214.515.5000
Contact Us

We're not around right now. But you can send us an email and we'll get back to you, asap.

Not readable? Change text.

Start typing and press Enter to search